Niagara Cutter SPC408 Cobalt Steel End Mill, General Purpose,

fewer flutes have more chip-carrying capacity and more flutes produce a finer finish Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel Uncoated (bright) tools have no additional surface...

fewer flutes have more chip-carrying capacity and more flutes produce a finer finish Titanium aluminum nitride (TiAlN) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better... Niagara Cutter SPC408 Cobalt Steel End Mill, General Purpose, TiAlN Coated, 4 Flutes, Square End, 5/16" Cutting Length, 5/16" Cutting Diameter Specification. The tool’s square end has straight cutting edges that create sharp, unrounded cuts, while the center-cutting design has cutting teeth at the end of the tool that support making pocket cuts, profiling, and slotting. The Niagara Cutter SPC408 TiAlN-coated cobalt steel square nose end mill has a 30-degree helix angle for milling a wide range of materials, including high-temperature alloys The number of flutes varies. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts.

Roughing end mills have chip-breaking cutting edges that remove material in less time than conventional end mills Fine-pitch tooth design is suitable for machining high-temperature alloys Titanium nitride (TiN) is a general-purpose coating that... Rougher end mills are special-purpose tools whose chip-breaking cutting edges create small chips for heavy cuts and remove more material in less time than conventional end mills, with minimal vibration (chatter). Each Niagara Cutter REM445 TiN-coated cobalt steel fine-pitch rougher end mill in this six-piece set has four flutes and a non-center-cutting design, making it suitable for machining dense materials such as high-temperature alloys. The tool’s square end creates sharp, unrounded cuts and has a corner chamfer on the cutting edges to provide more strength than standard square end tools in applications where cutting forces are high. Niagara Cutter REM445 Cobalt Steel End Mill Set, Fine-Pitch Roughing, TiN Coated, 4 Flutes, 6-piece Specification Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts. Each end mill has four flutes to optimize the feed and cut rate, and produces a rough finish that can be smoothed by a second finishing cut. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter.

fewer flutes have more chip-carrying capacity and more flutes produce a finer finish Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel Uncoated (bright) tools have no additional surface... Niagara Cutter SPC408 Cobalt Steel End Mill, General Purpose, Uncoated (Bright), 4 Flutes, Square End, 1-5/8" Cutting Length, 3/4" Cutting Diameter, 3/4" Shank Diameter Specification. The tool’s square end has straight cutting edges that create sharp, unrounded cuts, while the center-cutting design has cutting teeth at the end of the tool that support making pocket cuts, profiling, and slotting. The Niagara Cutter SPC408 uncoated (bright) cobalt steel square nose end mill has a 30-degree helix for milling a wide range of materials, including high-temperature alloys. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts.